3-WAY NORMALLY CLOSED (piped) Valve
PeterPaul explosion proof valves are used where fire or explosion hazards exist due to the presence of flammable gases or vapors, flammable liquids, combustible dust, or easily ignitable fibers. Hazardous Location valves are recommended, or in some cases compulsory, where a high level of protection from explosion is required.
- Miniature Hazardous Location valves using even less power than an EL53.
- Flame-proof construction.
- High quality engineering.
| MAX. OPER. PRESS. DIFF. | ORIFICE SIZE | CV FACTOR | VALVE NUMBER | ||
|---|---|---|---|---|---|
| DC | INLET | EXH | INLET | EXH | |
| 120 | 1/32 | 1/32 | .022 | .022 | ELL53GG8XCCM-∆ |
Ordering Information:
Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM
When ordering valves or repair packs add voltage and frequency to complete valve number. for examples: valve (ELL53GG8XCCM 120/60) repair pack (5KELL53GGX AC)
When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (OELL53GGDDCCM 120/60)
Operating Conditions
- Media
- Air and other common gases only.*
- Valve Temperature Range
- Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*
- Maximum Operating Pressure Differentials
- See table above.
- Burst Pressure
- 4000 PSI
- Leakage
- Bubble tight for standard valves.
- Vacuum
- To 5 Microns*
Electrical Characteristics
- Coil Voltage
- 12, 24/DC
- Nominal Power
- DC — .85 Watts
- Coil Construction
- Molded Class F with 3rd wire ground (Std.), Potted and Class H Option
- Typical Response Time on Air
- 4 - 16 Milliseconds
- Operating Speed
- Up to 600 CPM
- Duty Cycle
- Continuous
Mechanical Characteristics
- Internal Components
- Stainless Steel
- Elastomers
- Nitrile (Buna) (Std.). Many other elastomers available.*
- Orifice Diameter
- See table above.
- Porting
- 1/8" NPT (Std.)
- Housing
- Flame-Proof construction with 1/2" NPT conduit
- Listings
- Valves are UL listed and CSA certified for Hazardous Locations — Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G: Div 2, Groups A, B, C, D, E, F, and G.
- Certification
- North American
- Life Expectancy
- Millions of cycles, depending on application, lubrication, etc.
- Valve Weight
- 0.65 lbs
- Repair Packs
- See table above.
- Options
- Alternate Port Locations, Metering, Alternate Elastomers and All Stainless Steel Construction*
Series ELL50 Hazardous Location Valves
MODEL ELL53 3WNC PIPED EXHAUST EXPLOSION PROOF
MODEL ELL53 10-32 PORTS 3WNC PIPED EXHAUST EXPLOSION PROOF
MODEL ELL53 BODY OPTION "E" 3WNC PIPED EXHAUST EXPLOSION PROOF
MODEL ELL53 BODY OPTION "O" 3WNC PIPED EXHAUST EXPLOSION PROOF
MODEL ELL53 BODY OPTION "R" 3WNC PIPED EXHAUST EXPLOSION PROOF
MODEL ELL53 METERED BODY 3WNC PIPED EXHAUST EXPLOSION PROOF
sales@peterpaul.com
PeterPaul has created this page for you so you can calculate the flow or Cv (flow coefficient) to make the relationship visible between the pressure drop (the difference in pressure between two points of a liquid/gas carrying network) and the flow rate.
The use of this flow coefficient (Cv) calculator offers a standard calculation to compare valve capacities and sizing for a wide range of applications. The type and sizing of a valve or regulator can have a large impact on the performance of the assembly for transferring gas or liquids in the system.
Our sales department is ready to answer questions and to solve your valve needs. Please feel free to call, chat or email us.